Why This Popular Tire Size Fits Everyday Driving So Well
For drivers balancing comfort, predictable handling, replacement cost, and everyday practicality, 205/55R16 tires are a familiar sight. This tire size has been specified on many passenger cars across different markets and has consequently become widely available from numerous manufacturers. Its combination of moderate width, sidewall height, and 16-inch wheel fitment can work well for vehicles designed around this particular size.
Popularity alone, however, does not make 205/55R16 tires correct for every car with 16-inch wheels. Tire dimensions, load index, speed rating, construction, seasonal category, vehicle approval, and wheel compatibility all matter. Understanding the markings on the sidewall and following the vehicle manufacturer’s specifications are the safest ways to choose replacement tires without relying on size popularity alone.
What Do 205/55R16 Tires Mean
Tire sizing can look complicated until each part is separated.
The markings on 205/55R16 tires communicate several important dimensions and construction details. They do not, by themselves, provide every specification needed for replacement.
The numbers and letter indicate:
- 205 is the nominal section width in millimeters
- 55 is the aspect ratio
- R indicates radial construction
- 16 identifies the wheel rim diameter in inches
Additional markings normally appear after the size, such as a load index and speed symbol. Those specifications must also be considered when replacing tires.
What does 205 mean
The 205 designation refers to the nominal section width of 205/55R16 tires, expressed in millimeters.
It should not be interpreted as an exact tread-width measurement.
Actual physical dimensions can vary slightly between tire models because of construction, tread design, measuring rim, manufacturing tolerances, and applicable standards.
This is one reason two different 205/55R16 tires may not appear absolutely identical when placed side by side.
What does 55 mean
The second number is the aspect ratio.
For 205/55R16 tires, 55 means the nominal sidewall height is 55 percent of the nominal section width.
Using the basic nominal calculation:
205 × 0.55 = 112.75 millimeters
That gives a nominal sidewall height of approximately 112.75 mm. It should still be understood as part of the standardized size designation rather than a guarantee that every model measures exactly that amount in every installation.
What does R mean
The R identifies radial construction.
Radial construction is standard for modern passenger-car tires. It describes the general orientation of the tire’s structural cords relative to the direction of travel.
The R in 205/55R16 tires does not mean radius, racing, or rim.
This is a common misunderstanding when drivers first learn to interpret tire sidewalls.
What does 16 mean
The final number indicates the nominal wheel diameter that the tire is designed to fit.
Therefore, 205/55R16 tires are intended for compatible 16-inch rims.
A 16-inch diameter alone does not establish complete wheel compatibility. Rim width, offset, vehicle clearance, load requirements, brake clearance, and other fitment factors also matter.
Why 205/55R16 Tires Became So Popular
The popularity of 205/55R16 tires is closely tied to the vehicles manufacturers chose to fit with this size.
It has been used on many compact and midsize passenger cars, depending on model, year, trim, engine, region, and homologation.
As more vehicles use a particular size, replacement demand increases. Tire manufacturers and retailers then have a commercial reason to offer multiple products in that size.
The result is a broad selection of 205/55R16 tires across different price points and performance categories.
A useful middle ground for everyday cars
Vehicle engineers select tire sizes as part of a larger suspension, steering, braking, comfort, efficiency, packaging, and load-management system.
In appropriate vehicles, 205/55R16 tires provide dimensions that can suit normal road use without having an extremely low sidewall.
That can help explain why the size has appeared on many practical passenger vehicles.
It is important, however, not to attribute a car’s entire ride or handling behavior to tire size. Suspension tuning, tire model, pressure, vehicle weight, alignment, wheel construction, and road conditions also have major effects.
9 Powerful Benefits of 205/55R16 Tires for Everyday Cars
The advantages of this size are most meaningful when 205/55R16 tires are an approved specification for the vehicle.
Installing an unapproved tire size purely to obtain these benefits may introduce fitment, handling, legal, insurance, or speedometer issues.
1. Wide Choice of Replacement Tires
A significant practical advantage of 205/55R16 tires is product availability.
Because the size is common, drivers can often find products from major premium manufacturers, mid-market brands, and budget-oriented suppliers.
This gives buyers more opportunities to compare wet braking, noise, efficiency, seasonal suitability, durability, warranty coverage, and price.
Availability can also make emergency replacement easier than with an uncommon size, although local stock naturally varies.
2. Options Across Multiple Tire Categories
205/55R16 tires are available in several categories, depending on the regional market.
Drivers may find:
- Summer tires
- All-season tires
- Winter tires
- Touring tires
- Performance-oriented road tires
- Low-rolling-resistance models
- Reinforced or higher-load variants where applicable
- Run-flat versions for certain applications
These categories are not interchangeable simply because the size markings match.
A driver should choose the tire type according to climate, vehicle requirements, driving conditions, and applicable regulations.
3. Practical Sidewall Height
The 55-series aspect ratio gives 205/55R16 tires a nominal sidewall that is taller than many low-profile performance configurations.
A suitable sidewall can help provide compliance over road irregularities, though actual ride quality depends heavily on the specific tire construction and vehicle suspension.
This can be valuable for everyday cars driven over mixed road surfaces.
A taller sidewall relative to a low-profile alternative can also provide more distance between the wheel rim and the road, though no tire can guarantee protection against pothole damage.
4. Balanced Road Characteristics
Drivers often describe vehicles equipped with 205/55R16 tires as offering a useful balance between comfort and steering response.
That does not mean every tire in the size behaves the same way.
A soft touring tire can feel substantially different from a more performance-oriented product despite identical sidewall sizing.
This demonstrates why choosing 205/55R16 tires by dimensions alone is insufficient. Tire model and intended use can matter as much as the size printed on the sidewall.
5. Competitive Pricing Can Be Easier to Find
Common tire sizes benefit from broad market competition.
With many manufacturers producing 205/55R16 tires, buyers can often compare several suitable choices instead of relying on one specialist product.
Pricing still varies according to brand, technology, seasonal category, performance, region, retailer, and promotions.
The cheapest product is not automatically the best value. Braking performance, expected service life, fuel efficiency, warranty, noise, and climate suitability should all contribute to a purchasing decision.
6. Seasonal Availability
Drivers in climates with distinct seasons may have access to summer, winter, and all-season 205/55R16 tires.
This gives vehicle owners flexibility in choosing an appropriate strategy for local conditions.
Winter-tire requirements vary substantially by country and region. In some jurisdictions, winter or qualifying seasonal tires are legally required under certain conditions or during particular periods.
Always check current local rules rather than assuming one European or national standard applies everywhere.
7. Suitable Touring Choices Are Widely Available
Many people driving compact or family cars prioritize road noise, comfort, predictable wet behavior, and tread life rather than maximum dry-road cornering performance.
The market for 205/55R16 tires includes numerous touring-oriented options intended for these priorities.
Drivers should compare trustworthy independent testing where available.
Manufacturer marketing can describe intended performance, but comparative tests can help reveal how competing products perform under standardized conditions.
8. Replacement Availability Can Simplify Ownership
Tires eventually need replacement because of tread wear, damage, age-related deterioration, or changes that make continued use inappropriate.
A commonly stocked size can make this process easier.
Drivers traveling away from home may also have a better chance of finding 205/55R16 tires than an unusual specification, although no retailer can guarantee immediate stock.
Commonality is therefore an ownership convenience rather than a technical performance advantage.
9. Familiarity Among Tire Shops
Because 205/55R16 tires are common, professional tire installers routinely encounter the size.
That can simplify routine sourcing and installation.
Professional familiarity does not remove the need to verify the complete vehicle specification.
A technician still needs to consider load index, speed rating, tire type, pressure requirements, axle matching, vehicle manufacturer guidance, and condition of the wheels and existing tires.
Are 205/55R16 Tires Right for Your Car
The correct tire size is determined primarily by the vehicle manufacturer’s approved specifications.
Do not assume that 205/55R16 tires fit merely because the car currently has 16-inch wheels.
Check the owner’s manual, tire-information placard, manufacturer documentation, or other authoritative vehicle information.
Depending on region and vehicle, approved alternate sizes may also be documented.
Model name alone is not enough
A single vehicle model may have several tire specifications.
Differences can depend on:
- Model year
- Trim level
- Engine
- Wheel package
- Suspension
- Market
- Vehicle weight
- Factory options
For example, two visually similar versions of a car may require different tire dimensions or load ratings.
When purchasing 205/55R16 tires online, use exact vehicle information rather than relying solely on the model name.
Understanding Load Index
The load index normally follows the tire-size marking.
For example, a sidewall may show a format such as 205/55 R16 followed by a numerical load index and speed symbol.
The load index corresponds to the maximum load the tire is rated to carry under specified conditions.
Drivers should use a tire meeting the vehicle manufacturer’s required specification.
Do not downgrade load capacity casually
A tire physically fitting the rim does not mean it has an appropriate load rating.
Using inadequate load capacity can compromise safety.
Some 205/55R16 tires may also carry reinforced or extra-load designations. These should be selected according to vehicle requirements rather than on the assumption that a higher rating is automatically preferable in every situation.
Ask a qualified tire professional when the correct rating is uncertain.
Understanding Speed Ratings
The speed symbol indicates a tire’s standardized speed capability under specified test conditions.
It should never be interpreted as encouragement to drive at that speed.
Vehicle manufacturers specify suitable ratings according to vehicle requirements, and legal requirements may also apply.
Replacement 205/55R16 tires should comply with the applicable vehicle and regional specifications.
Seasonal tire rules can affect permitted substitutions in some jurisdictions, making authoritative local guidance important.
Summer 205/55R16 Tires
Summer tires are generally designed to perform in warmer conditions, with compounds and tread patterns optimized around those intended operating conditions.
They can provide strong dry and wet road performance when temperature and weather are appropriate.
They are not intended to substitute for suitable winter tires in severe cold, snow, or ice.
Drivers choosing summer 205/55R16 tires should compare wet braking, aquaplaning performance, efficiency, noise, and wear characteristics rather than judging by tread appearance alone.
Who should consider summer tires
Summer tires can make sense where climate and regulations support seasonal use or where drivers switch to dedicated winter tires during colder months.
The decision should consider the entire year rather than only current weather.
A driver purchasing 205/55R16 tires during summer should know what will happen when temperatures fall.
Winter 205/55R16 Tires
Winter tires use tread designs and compounds intended for cold-weather conditions.
Depending on the specific tire and certification, they can improve traction and braking in winter conditions relative to unsuitable warm-weather tires.
For drivers facing regular snow, ice, and low temperatures, suitable winter 205/55R16 tires can be an important part of seasonal vehicle preparation.
Check required winter markings
Tire markings and legal requirements differ by jurisdiction.
The Three-Peak Mountain Snowflake symbol, often abbreviated 3PMSF, identifies tires meeting a standardized snow-performance requirement.
Drivers should check the regulations applying in the countries or regions where they travel.
This is particularly important during cross-border winter journeys because rules can differ.
All-Season 205/55R16 Tires
All-season tires are designed as a compromise across a wider range of conditions.
Modern all-season 205/55R16 tires can be convenient for drivers who experience moderate seasonal variation and prefer not to switch between two sets.
The compromises vary between products.
Some prioritize winter capability, while others behave more like summer-oriented tires with additional cold-weather capability.
All-season does not mean ideal for every condition
A single tire cannot maximize performance under every combination of heat, heavy rain, snow, ice, comfort, wear, and efficiency.
Drivers in demanding winter environments may still prefer dedicated winter tires.
Those in consistently warm climates may prioritize summer products.
Choosing all-season 205/55R16 tires should therefore be a climate and driving decision rather than simply a convenience decision.
Wet Performance Matters More Than Many Drivers Realize
Dry-road handling receives considerable attention in tire advertising, but ordinary drivers frequently encounter rain.
Wet braking and aquaplaning resistance can be important differentiators between 205/55R16 tires.
Tread depth, compound, tread design, road surface, speed, tire pressure, and water depth all affect wet performance.
Even excellent tires cannot overcome unsafe speed in standing water.
Tread depth changes performance
As tires wear, their ability to manage water can change.
Legal minimum tread-depth requirements vary by jurisdiction, and safety considerations may lead drivers to replace tires before reaching an absolute legal minimum depending on condition and intended use.
Inspect 205/55R16 tires regularly rather than waiting for a scheduled service.
Uneven wear can also indicate pressure, alignment, suspension, or other issues requiring investigation.
Tire Pressure and 205/55R16 Tires
Correct tire pressure is determined by the vehicle manufacturer, not by the generic tire size.
Two cars using identical 205/55R16 tires may specify different pressures because vehicle weight and engineering requirements differ.
Use the pressure information provided on the vehicle placard or in authoritative manufacturer documentation.
Do not use the maximum pressure printed on a tire sidewall as the normal inflation target unless specifically instructed by the relevant vehicle documentation.
Check pressure when appropriate
Tire pressure changes with temperature and can decrease gradually over time.
Regular checks help maintain handling, tire wear, efficiency, and load capability.
Measure pressure according to manufacturer guidance, typically under conditions intended to represent a cold tire.
If one of the 205/55R16 tires repeatedly loses pressure, investigate for a puncture, valve issue, wheel problem, or other leak rather than continually adding air.
How 205/55R16 Tires Affect Ride Comfort
Sidewall dimensions influence how a tire responds to road irregularities, but they are only one part of ride comfort.
Tire construction, inflation pressure, wheel weight, suspension design, seat design, vehicle structure, and road surface also matter.
Consequently, switching between different 205/55R16 tires can noticeably change comfort even though the nominal dimensions remain identical.
Touring-focused products may prioritize refinement, while performance tires may prioritize steering response and grip.
Noise is tire-specific
Road noise depends partly on tread design, pavement, vehicle insulation, tire construction, and wear.
Drivers who spend considerable time on motorways may prioritize quieter 205/55R16 tires.
Regional tire labels and independent tests may provide useful information about noise, although external noise ratings do not necessarily describe exactly what occupants hear inside every vehicle.
Use several relevant criteria when comparing products.
Fuel Efficiency and Rolling Resistance
A tire deforms as it rolls, and some energy is lost through that process.
Rolling resistance contributes to vehicle energy consumption, making tire design relevant to fuel economy and electric-vehicle range.
Some 205/55R16 tires prioritize low rolling resistance.
However, tire design involves compromises among efficiency, wet grip, durability, comfort, handling, and other characteristics.
Pressure also affects efficiency
Underinflation can increase rolling resistance and generate excessive heat.
Maintaining the vehicle manufacturer’s recommended tire pressure is therefore one of the simplest ways to support efficient operation.
Do not overinflate 205/55R16 tires in an attempt to reduce rolling resistance.
Excess pressure can alter ride, handling, wear, and available grip and may move the tire outside the vehicle’s intended setup.
How Long Do 205/55R16 Tires Last
There is no fixed mileage lifespan for every tire in this size.
Tread life depends on tire design, rubber compound, driving style, road conditions, alignment, inflation, vehicle weight, rotation practices where applicable, climate, and maintenance.
Two sets of 205/55R16 tires can consequently provide very different service lives.
Warranty mileage, where offered, should also be read carefully because conditions and exclusions apply.
Age matters as well as tread
A tire can deteriorate with time even when tread remains.
Manufacturers and safety authorities may provide recommendations regarding inspection or replacement as tires age.
Check the tire’s manufacturing-date marking and follow applicable manufacturer guidance.
Cracking, bulges, exposed cords, impact damage, or other serious deterioration on 205/55R16 tires deserves professional assessment regardless of tread depth.
How to Read a Tire Manufacturing Date
Tire sidewalls typically carry a DOT-related identification code in markets where that marking applies.
The final four digits of the relevant date code identify the manufacturing week and year.
For example, a code ending in 2425 would indicate production during week 24 of 2025.
This information can help buyers evaluate the age of 205/55R16 tires.
The manufacturing date does not by itself determine remaining service life because storage conditions and subsequent use also matter.
Replacing Two or Four Tires
Replacing all four tires can provide the most consistent performance when all are similarly worn.
Sometimes only two need replacement.
Vehicle drivetrain, tire condition, tread differences, manufacturer guidance, and tire type should influence the decision.
Many tire and vehicle manufacturers provide specific recommendations about where a new pair should be installed.
Drivers using 205/55R16 tires should follow authoritative guidance rather than assuming new tires always belong on the powered axle.
All-wheel-drive vehicles may have tighter requirements
Some all-wheel-drive systems can be sensitive to differences in tire circumference or tread depth.
A mismatched set could potentially affect drivetrain operation depending on vehicle design.
Owners should consult their vehicle manufacturer’s requirements before replacing only one or two 205/55R16 tires on an AWD vehicle.
This is an area where saving money on one tire can become expensive if the vehicle has stricter matching requirements.
Mixing Tire Brands and Models
Using matching tires across an axle is generally preferable, subject to manufacturer requirements and local law.
Different tire models can have different tread patterns, compounds, grip characteristics, and responses to changing conditions.
For this reason, four tires showing the same 205/55R16 size are not automatically equivalent.
Some vehicles have specific requirements for approved tire combinations.
When replacing a damaged tire, consult the vehicle manufacturer or qualified tire specialist when matching is uncertain.
Run-Flat 205/55R16 Tires
Some vehicles may use run-flat tires designed to permit limited continued mobility after certain pressure-loss events, subject to the tire manufacturer’s restrictions.
Not every car using 205/55R16 tires is designed for run-flat operation.
Switching between run-flat and conventional tires can affect vehicle behavior and roadside mobility planning.
Before making that change, check vehicle and tire manufacturer guidance.
Run-flat does not mean puncture-proof
Run-flat tires can still be damaged and eventually require repair or replacement.
Distance and speed limitations apply after pressure loss, depending on the product.
A tire-pressure monitoring system is particularly important in run-flat applications because a driver may not immediately notice pressure loss through handling alone.
205/55R16 Tires on Electric and Hybrid Cars
Some electric and hybrid vehicles may use this tire size depending on model and specification.
EVs can place particular demands on tires because of vehicle mass, immediate torque delivery, efficiency priorities, and low powertrain noise.
If an EV specifies 205/55R16 tires, replacements should meet the manufacturer’s load and other requirements.
An EV-branded tire is not automatically mandatory unless specified, but suitability should be verified.
Rolling resistance can affect range
Tire rolling resistance can influence energy consumption in an electric vehicle.
However, choosing a tire solely for efficiency can overlook wet braking, durability, noise, and handling.
Drivers should select 205/55R16 tires that offer an appropriate balance for the vehicle and driving environment.
Can You Change From Another Size to 205/55R16 Tires
Changing tire size is more complex than finding a combination with approximately the same overall diameter.
Wheel width, load capacity, clearance, suspension geometry, speedometer calibration, braking systems, legal requirements, and manufacturer approval can all matter.
Do not switch to 205/55R16 tires simply because an online calculator suggests the diameter is close.
Use an approved alternative specified by the vehicle manufacturer or obtain competent professional guidance.
Overall diameter matters but is not everything
A significantly different rolling circumference can affect displayed speed and distance as well as vehicle systems.
Yet matching diameter alone does not guarantee suitability.
The tire still has to fit the wheel correctly, clear surrounding components throughout suspension and steering movement, and meet load and performance requirements.
Proper fitment is a complete system question.
Common Buying Mistakes With 205/55R16 Tires
One common mistake is selecting tires based solely on price.
Another is buying the correct dimensions but the wrong load index or speed rating.
Drivers also sometimes overlook seasonal suitability, buying a summer-oriented tire in a climate requiring meaningful winter capability.
Other mistakes include purchasing tires significantly older than expected without checking the date, mixing incompatible tire types, and assuming every product in the same size performs similarly.
The wide selection of 205/55R16 tires is valuable only when drivers compare specifications that actually matter.
How to Compare 205/55R16 Tires
Start by confirming the exact specification required by the vehicle.
Then identify the conditions in which the car is driven most frequently.
For ordinary road use, useful comparison factors can include:
- Wet braking performance
- Dry braking and handling
- Aquaplaning resistance
- Seasonal capability
- Rolling resistance
- Ride comfort
- Road noise
- Wear characteristics
- Manufacturer warranty
- Independent test performance
- Purchase and installation cost
Prioritize safety-related performance before cosmetic tread appearance or brand familiarity.
Independent tests can be especially useful
Well-designed comparative tire testing can reveal differences that cannot be identified by looking at tread patterns.
A tire performing exceptionally in one area may be average in another.
When reviewing tests of 205/55R16 tires, check whether the exact model, generation, size, and relevant test conditions match what you are considering.
Results from a different tire model within the same brand should not automatically be transferred to another product.
Budget Versus Premium 205/55R16 Tires
Price categories do not guarantee performance.
Premium manufacturers often invest heavily in research, materials, testing, and product development, but each tire still deserves evaluation according to objective performance.
Budget 205/55R16 tires can differ substantially from one another.
The safest approach is to evaluate credible comparative testing and required specifications rather than assuming the most expensive or least expensive tire is automatically the correct choice.
Consider total value
Purchase price is only one part of tire ownership.
Tread life, efficiency, braking performance, comfort, noise, warranty, and seasonal suitability can influence total value.
A cheaper tire replaced substantially earlier may not ultimately save money.
Conversely, paying for capabilities an ordinary commuter never needs may provide limited practical benefit.
Maintaining 205/55R16 Tires
Good tires still require maintenance.
Inspect the tread and sidewalls regularly. Maintain correct pressure, investigate unusual vibrations, and have alignment checked when there are signs of uneven wear or after relevant suspension impacts.
Rotation can help equalize wear on vehicles where the manufacturer recommends it and the tire setup permits it.
Directional or staggered configurations can limit rotation patterns.
Watch for uneven wear
Wear concentrated on one edge, both shoulders, or the center can indicate underlying problems.
Possible factors include pressure, alignment, suspension condition, driving style, or vehicle loading.
Do not assume that abnormal wear on 205/55R16 tires is simply a characteristic of the tire.
Finding the cause can prevent a replacement set from developing the same pattern.
When 205/55R16 Tires Need Immediate Attention
Some tire problems should not wait until the next routine service.
A visible bulge can indicate internal structural damage. Exposed cords, substantial cuts, sudden pressure loss, severe cracking, or significant impact damage can also require prompt professional evaluation.
Do not intentionally continue normal driving on a visibly compromised tire.
If a 205/55R16 tire loses pressure while driving, respond according to the vehicle and tire manufacturer’s safety guidance and stop in a safe location when appropriate.
Why Proper Installation Matters
Even an excellent tire can perform poorly when installed incorrectly.
Professional fitting typically includes appropriate mounting, inflation, balancing, valve service where applicable, and inspection of the wheel.
Tire-pressure monitoring systems may require specific procedures.
Correct wheel-bolt or lug-nut tightening is also critical and should follow the vehicle manufacturer’s torque specification and installation process.
After fitting new 205/55R16 tires, follow any inspection or retorque guidance applicable to the vehicle and wheel type.
Why This Size Remains a Go-To Choice
The continued popularity of 205/55R16 tires comes from more than one performance characteristic.
Many vehicles were engineered to use the size, creating a large installed base. That demand encourages broad manufacturer participation, which gives drivers numerous replacement choices.
The dimensions also suit the priorities of many everyday passenger vehicles when specified by their manufacturers.
Drivers can choose among comfort-focused, efficient, seasonal, and more performance-oriented 205/55R16 tires without necessarily changing wheel size.
That flexibility is a major reason the specification remains relevant even as larger wheels have become common on newer vehicle trims.
FAQ’s
What does 205/55R16 mean on a tire?
205 is the nominal section width in millimeters, 55 is the aspect ratio, R indicates radial construction, and 16 is the compatible nominal rim diameter in inches.
Are 205/55R16 tires good for everyday driving?
They can be an excellent everyday specification when approved for the vehicle. Actual comfort, grip, noise, efficiency, and wear depend heavily on the specific tire model.
Can 205/55R16 tires fit any 16-inch wheel?
No. Rim diameter is only one fitment factor. Wheel width, vehicle clearance, load requirements, manufacturer approval, and other specifications must also be correct.
What pressure should 205/55R16 tires use?
Use the vehicle manufacturer’s recommended pressure shown on the vehicle placard or authoritative documentation. Tire size alone does not determine the correct inflation pressure.
Are 205/55R16 tires available as winter tires?
Yes. Winter, summer, and all-season models are widely available in this size, although availability and required winter markings vary by market.
How long do 205/55R16 tires last?
There is no universal lifespan. Tire model, pressure, alignment, roads, climate, driving style, vehicle weight, maintenance, damage, and age all influence replacement timing.
Conclusion
205/55R16 tires remain a go-to specification for many everyday cars because they combine widespread availability with a broad choice of touring, summer, winter, all-season, efficient, and performance-oriented products. Their dimensions can provide a practical balance of sidewall height and width for vehicles engineered around this size, while strong market competition gives owners considerable flexibility when replacement time arrives.
The right 205/55R16 tires are ultimately those that meet the complete specification of the car and perform well in the conditions where it is actually driven. Confirm size, load index, speed rating, seasonal requirements, and manufacturer recommendations before buying. Combine a suitable tire with correct pressure, regular inspection, proper installation, and sensible driving to get the safety and everyday usability this popular size is capable of delivering.
